PLUMBING BASICS: BEFORE INSTALLING A BATHTUB

Plumbing Basics: Before Installing a Bathtub

Plumbing Basics: Before Installing a Bathtub

Blog Article

Click Here

Have you been trying to find selective information around How to Install a Bathtub Yourself?


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Mounting a bathtub isn't exactly brain surgery, yet it does require strong plumbing, carpentry, as well as sometimes, tiling skills. Changing an old bath tub with a new one is additionally a reasonably hard project. If the old bathtub is conveniently obtainable, the job can relocate easily; if you have to open a wall to eliminate the old bathtub as well as position the new tub, the job is a lot harder. In either case, the project is within a residence handyman's abilities, although you will require a helper to vacate the old bathtub as well as embeded in the new one. Make certain you have actually qualified yourself for the work as well as are comfortable trying it. Rather than working with a contractor to take control of a halfway-completed project, it is far better to take into consideration utilizing one prior to you begin. Opportunities are you may require a professional plumber to make tube connections.
This short article will certainly help you install a brand-new bathtub in your restroom if you have currently purchased a brand-new bathtub and also don't need to alter the setup of your previous water pipelines.
Your devices and material list should consist of the following:
  • New Bathtub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipe Caps


  • Getting ready for the Setup


    First of all, the supporting structure provided with the bath needs to be fitted (if called for) according to the manufacturer's directions. Next, fit the taps or mixer to the tub. When suitable the tap block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted between the bath and the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets unit to avoid pressure on the tub.
    Fit the versatile faucet adapters to the bottom of the two taps using 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet with the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. See to it you use every one of the supplied washing machines.
    Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its last setting.

    Removing Old Taps


    If you need to replace old faucets with brand-new ones as a part of your setup, after that the first thing you need to do is separate the water supply. After doing so, activate the faucets to drain pipes any type of water staying in the system. The process of getting rid of the existing taps can be rather problematic due to the limited accessibility that is usually the situation.
    Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a cloth all set for the continuing to be water that will originate from the pipelines. Once the supply pipelines have been gotten rid of, use the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the single faucets from turning during this process. Once the faucets have actually been removed, the holes in the bath/basin will need to be cleansed of any type of old sealing compound.
    Prior to going on to fit the new taps, compare the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.

    Mounting the Tub


    Utilizing the two wooden boards under its feet, put the bath tub in the called for placement. The wooden boards are useful in evenly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 tiny factors.
    The next goal is to guarantee that the tub is leveled all round. This can be attained by inspecting the level and changing the feet on the tub until the spirit level checks out degree.
    To mount faucets, fit all-time low of the outermost adaptable tap adapter to the appropriate supply pipe by making a compression join; after that do the very same for the various other tap.
    Switch on the supply of water as well as examine all joints and new pipework for leakages as well as tighten them if essential. Load the tub and also examine the overflow outlet as well as the normal outlet for leakages.
    Ultimately, take care of the bath paneling as described in the maker's user's manual. Tiling and also sealing around the bath tub needs to wait up until the bathtub has actually been made use of a minimum of when as this will resolve it right into its last placement.

    Fitting New Touches


    If the tails of the new taps are plastic, then you will need a plastic connector to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet and the other end provides a connection to the existent supply pipelines.
    If you need to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
    Next off, place the faucet in the placing hole in the bath/basin guaranteeing that the washers remain in place between the tap and also the sink. Safeguard the faucet in position with the manufacturer supplied backnut. As soon as the faucet is safely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical tap ports. The previous type must be linked to the faucet finishes initially, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been linked.

    Tiling Around the Bathtub


    In the location where the bathroom meets the tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to split a rigid seal, triggering the water to permeate the wall surface between the bath as well as the tiling, resulting in issues with wetness and also feasible leaks to the ceiling listed below.
    You can pick from a variety of coloured sealants to assimilate your components and also fittings. They are sold in tubes as well as cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked newspaper or soft rope. Bear in mind to always fill up the tub with water prior to securing, to allow for the activity experienced when the bathtub is in use. The sealer can break rather early if you do not consider this activity before securing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of water-resistant or water resistant glue as well as cement.

    Bathtub Installation


    How Important Is A Bathtub To Your Home?


    High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


    Install Piping Before Tub


    You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


    Position the Tub


    Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



    NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


    Assemble Drain Connections


    Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


    Place a Pipe For the Shower Head


    First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


    Attaching Hot and Cold Water Lines


    Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


    Install the Spout


    Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



    NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


    Check For Leaks


    Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


    estore the Bathroom Wall


    Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

    https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


    A Step-by-Step Guide to Installing a Bathtub

    We hope you liked our article about A Step-by-Step Guide to Installing a Bathtub. Thanks for spending some time to read through our posting. For those who enjoyed our article plz make sure you remember to pass it around. Bless you for your time. Visit again soon.


    Save time, dial!

    Report this page